EN
BPE series DC power type, Solid state output type
Sensitivity adjusterTimer function: ON Delay, OFF Delay, One-shot DelayNPN/PNP open collector output (Dc power type)Self-diagnosis function (green LED turns on in stable level)Wide power supply range: Universal 24-240VDC/24-240VACProtection structure lP66 (lEC standard)
- Overview
- Related Products
| Model | Standard type | BPE-QL15M | BPE-KL5M | BPE-EL3M | BPE-CL70 |
| With Timer | BPE-QL15M-T | BPE-KL5M-T | BPE-EL3M-T | BPE-CL70-T | |
| Sensing type | Through-beam | Retro-Reflection | Retro-Reflection (with polarizing filter) |
Diffuse Reflection | |
| Sensing Range | 15M | 5M | 3M | 700mm | |
| Sensin target | Opaque materials of Min.Φ15mm |
Opaque materials of Min.Φ60mm | Transparent, Opaque materials |
||
| Hysteresis | ----------------- | Max.20% at rated setting distance |
|||
| Response time | Max.1ms | ||||
| Power supply | 12 - 24 VDC ± 10 % (Ripple P-P:Max.10%) | ||||
| Current consumption | Max.50mA | ||||
| Light source | Infrared LED(850nm) | Red LED(660nm) | Infrared LED(940nm) | ||
| Sensitivity adjustment | Sensitivity adjuster | ||||
| Operation mode | Light ON/Dark ON operation mode switch | ||||
| Control output | NPN or PNP open collector output Load voltage: max. 30VDC Load current: max.200mA Residual voltage - NPN:max.1VDC PNP: max.2.5VDC |
||||
| Self-diagnosis output | NPN open collector output (green LED turns on at stable operation and output (transistor output) turns on) Load voltage: max.30VDC Load current: max.50mA Residual voltage -max.1VDC(50mA) max. 0.4VDC(16mA) |
||||
| Protection circuit | Reverse polarity protection circuit, output short overcurrent protection circuit | ||||
| Timer function | Selectable ON delay, OFF delay, one shot delay by slide switch [delay time: 0.1 to 5 sec (timer adjuster)] |
||||
| Indicator | Operation indicator: yellowLED, self-diagnosis indicator: green LED | ||||
| Connection | Terminal connection | ||||
| Insulation resistance | Min.20MΩ (at 500VDC mega ) | ||||
| Insulation type | Double or strong insulation(dielectric voltage between the measured input and the power : 1.5 kV) |
||||
| Noise strength | ±240V the square wave noise (pulse width:1㎲)by the noise simulator | ||||
| Dielectric strength | 1500VAC 50/60Hz for 1minute | ||||
| Vibration | Mechanical | 1.5mm amplitude at frequency of 10 ~ 55Hz in each of X, Y,2 directions for 2 hours | |||
| Malfunction | 1.5mm amplitude at frequency of 10 ~ 55Hz in each of X, Y,2 directions for 10 minutes | ||||
| Shock | Mechanical | 500 m/s2(50G)in X,Y,Z directions for 3 times | |||
| Malfunction | 100 m/s2(10G)in X,Y,Z directions for 3 times | ||||
| Environ- ment |
Ambient illu. | Sunlight :Max.11,000lx , Incandescent lamp:Max.3,000lx (receiver illumination) | |||
| Ambient temp. | -20~+65℃ C27(at non-freezing status),Storage:-25~+70℃ | ||||
| Ambient humi. | 35~85%RH, Storage:35~85%RH | ||||
| Material | Case, lens cover: polycarbonate, sensing part: acrylic, bracket, bolt, nut: steel chromium molybdenum |
||||
| Protection | IP66(IEC standard) | ||||
